Hammer level meter, intelligent level meter I. Overview hammer level meter for container powders, granules and liquid level monitoring hoppers, silos, storage tanks or near real-time measurement of weight. It does this by direct measurement of the top non-material spatial distance, indirect measurements to within the material layer height of the material objects, and can choose to configure different conditions according to a variety of flange, weight and operator interface or remote communication, to achieve a humane, rational and scientific design purposes. Wherein the level measurement QHYC-Ⅰ series for the metallurgical industry, QHLC-Ⅰ series for level measurement of grain and oil processing industry. Second, the main component works hammer level meter are: weight, mounting flange, measuring mechanism, soot blower, guide wheels, wire rope, wire rope reel, the pendulum mechanism, control unit, motor, control unit, metering unit and electrical interfaces. When the sensor is connected to the probe command, the motor is transferred, after driving the winding drum rotation speed reduction mechanism, cable decentralization, hammer follow its decline, when the hammer drops the material surface is lifted material surface and weight loss, relaxation rope , the Hall element sensitive lever action movement and position signal to the controller, to obtain motor reverse command issued immediately after the signal, the weight with rope rising return until the hammer back to its original position warehouse roof, electrical stop complete a detection process. And 4-20mA current signal, the standard MODBUS serial communication, dry contact transmission in three ways to the DCS system or external display unit and alarm material level. Third, the technical parameters ◆ Supply voltage: 220 V ± 10% AC, 50 Hz ◆ Power consumption: 15VA continuous, 40 VA intermittent ◆ Ambient temperature: -40 ° F to 150 ° F (-40 ° C to 65 ° C) ◆ medium temperature: less than 130 ° C ◆ measuring range: 46.9 m ◆ measurement speed: 0.26 m / s ◆ Accuracy: <0.25% ◆ reproducible measurement distance: 20 mm ◆ Resolution: 3.5mm ◆ cable: 1.0mm (123kg Tension) ◆ weight Weight:? 0.89Kg four or five wiring, dimensions and installation method ???????????????? 1, hammer level meter should be installed in loading material deviation feed inlet location. Level meter optimum installation location should be at least 1.2 meters away from the entrance charge. From the container sidewall should as far as possible, at least 1 meter. 2, hammer level meter can be mounted on top of most of the container. Level meter must be installed on the flange and make sure that natural vertical plumb, so that plumb / cable device is directly fall. If not the level of the top container in the previous section must be welded steel pipe, the flange can be installed horizontally. The upper and lower flange gaskets to be added to ensure a good seal between the two flanges. Sixth, application case 1, lime kiln top level measurement 2, loose flour bin level measurement Henan latent co-Automation Technology Co., Ltd. "latent together" named in the "painstaking fine cast, dedicated efforts and sincerity" (abbreviation SQ also from the Service better in Quality best). The company was founded in 2007, now has over Shanghai Electrical and Mechanical Equipment Co. latent, latent Shanghai Electric Equipment Co., Ltd. and Henan together the potential co-Automation Technology Co., Ltd. three subsidiaries. The company and Siemens, Schneider, ABB, OMRON, Mitsubishi and other manufacturers, mainly to metallurgy, environmental protection, polysilicon and other sectors of automation engineering. Product Advisory: 0373-2651333 2652333 Technical support: 0373-5078599 5078977 Service: 4,000,373,863 18,603,802,255 (Yang) Note :( plane: Monday to Saturday 8:00 ~ 18:00 Mobile: 7 × 24-hour service) Fax: 0373-3512971 E-mail: info@hnqianhe.com Company Address: Xinxiang City, Henan Province Torch High-tech Zone Park Comprehensive R & D Building ---- bangqi